Cisco C9600-SUP-1 Datasheet
The Cisco C9600-SUP-1 is a switch supervisor engine in the Catalyst 9600 series. Every figure below is quoted from Cisco official documentation.
5.45 KgWeight
1.7 x 15.0 x 13.41”Dimensions (H x W x D)
Key Specifications
| System Switching Capacity | Up to 9.6 Tbps (4.8 Tbps full-duplex) |
|---|---|
| Per-slot Switching Capacity | Up to 2.4 Tbps (1.2 Tbps full-duplex) |
| ASICs | 3x UADP 3.0 |
| Forwarding Rate | 3 Bpps (1 Bpps per ASIC) |
| DRAM | 16 GB |
| Flash | 16 GB |
| SSD capacity | Up to 960 GB |
| VLAN IDs | 4,094 |
| PVST Instances | 1,000 |
| STP Virtual Ports (PortVLANs) for PVST | 16,000 |
| STP Virtual Ports (Port VLANs) for MST | 100,000 |
| Switched Virtual Interfaces (SVIs) | 1,000 |
| Jumbo Frames | 9,216 |
| Total number of MAC Addresses | Up to 128,000 |
| Total number of IPv4 Routes | Up to 256,000 (indirect + direct) |
| Total number of IPv6 Routes | Up to 256,000 |
| Address Resolution Protocol (ARP) entries | Up to 90,000 |
| Neighbor Discovery Protocol (NDP) entries | Up to 128,000 |
| IGMP/MLD Snooping entries | Up to 16,000 |
| Multicast Routes | Up to 32,000 |
| QoS ACL Scale (IPv4/IPv6) | Up to 16,000/8,000 |
| Security ACL Scale (IPv4/IPv6) | Up to 27,000/13,500 |
| GRE Tunnels | Up to 1,024 |
| MACsec sessions | Up to 2,000 |
| NetFlow entries (IPv4/IPv6) | Up to 384,000 (full, 128,000 per ASIC) |
| Packet Buffer | Up to 108 MB (36 MB per ASIC) |
| Maximum bandwidth per slot | 2.4 Tbps (1.2 Tbps full-duplex) |
| Minimum software requirement | IOS XE 16.11.1 |
| Maximum 100G ports (Catalyst 9606R chassis) | 48 |
| Maximum 40G ports (Catalyst 9606R chassis) | 96 |
| Maximum 25G ports (Catalyst 9606R chassis) | 192 |
| Maximum 10G ports (Catalyst 9606R chassis) | 192 |
| Maximum 5G ports (Catalyst 9606R chassis) | 192 |
| Maximum 2.5G ports (Catalyst 9606R chassis) | 192 |
| Maximum 1G ports (Catalyst 9606R chassis) | 192 |
| Maximum 100M ports (Catalyst 9606R chassis) | 192 |
| Maximum 10M ports (Catalyst 9606R chassis) | 192 |
| Dimensions (H x W x D) | 1.7 x 15.0 x 13.41” (4.32 x 38.1 x 34.06 cm) to faceplate 1.7 x 15.0 x 15.7” (4.32 x 38.1 x 39.88 cm) to ejector |
| Weight | 5.45 Kg (12.02 lbs) |
| Rack Units (RU) | 1 RU |
| Operating Temperature | -5° to 45° C (23° to 113° F) up to 6,000 feet -5° to 40° C (23° to 104° F) up to 10,000 feet |
| Storage Temperature | -40° to 70° C (40° to 158° F) |
| Relative Humidity, Operating and Non- operating, Non-condensing | 10% to 95%, noncondensing |
| Altitude | -60 to 3,000 m (-197 to 9843 feet) |
| Mean time between failures (MTBF) | 271,420 |
Specifications are quoted verbatim from the Cisco official data sheet; no values are estimated.
Frequently Asked Questions
What is the Cisco C9600-SUP-1?
The Cisco C9600-SUP-1 is a switch supervisor engine in the Catalyst 9600 series. Every figure below is quoted from Cisco official documentation.
What are the dimensions of the Cisco C9600-SUP-1?
It measures 1.7 x 15.0 x 13.41” (4.32 x 38.1 x 34.06 cm) to faceplate 1.7 x 15.0 x 15.7” (4.32 x 38.1 x 39.88 cm) to ejector (H x W x D).
How much does the Cisco C9600-SUP-1 weigh?
It weighs 5.45 Kg (12.02 lbs).
Need current pricing or availability for the Cisco C9600-SUP-1? See the C9600-SUP-1 product page or request a quote.